Failing Hard with the Bramble Berry Rose Gold Bath Bomb Kit

A few weeks ago, Bramble Berry was advertising their rose gold bath bomb kit and I decided to grab one.   I don’t care for rose scented things, but I generally carry most of the items needed to create bath bombs from my other crafts and I thought this might be something I’d be interested in trying.  So why not get a kit to try it out.

I paid $28 including tax.  Shipping was free for this promotion.

Bramble Berry Rose Gold Bath Bomb Kit

Opening up the box, I found a beautifully packed box.  I’ve ordered from Bramble Berry many times in the past, they always pack the supplies well.  They even tape the bottles shut in case of a leak.

Continue reading “Failing Hard with the Bramble Berry Rose Gold Bath Bomb Kit”

DIY Wire Soap Loaf Cutter ($12)

Curing Soaps

My soap collection has been slowly building.  One thing I’ve noticed is that the bars are rarely uniformly cut.   No matter how hard I try that cheap little soap cutter is just doing a poor job.

I’m talking about one of these bamboo box jobbers with a  planer:

It seems like it would work well, but there’s too much play in the gap where the knife goes.  And these boxes are never tall enough for your soap, so the first inch or so of soap cutting you’re pretty much guessing where you should cut until you hit the slot for the knife.

Continue reading “DIY Wire Soap Loaf Cutter ($12)”

How to make Cold Process Soap

I’ve been thinking about making cold process soap for years and I often watch videos on soap design on YouTube. When my friend asked me to pick up his favorite coconut soap while I was at the store and I found it was $5+ a bar! $20 in soap later, I decided it was finally time to give it a shot.

Most of the materials below will either link you to BrambleBerry or Amazon. These were the two main shopping sources I used to buy my materials. BrambleBerry is a popular supplier and also happens to be local, so I knew my shipping would be relatively fast.

You should keep in mind that most of the equipment you use will come in contact with lye and should be dedicated to soap making. Don’t eat from, drink from or make food with these tools or in these containers afterwards.

materials for soap making

Continue reading “How to make Cold Process Soap”

Making Photopolymer Stamps: Materials List & Pictorial

So you want to start making photopolymer stamps? I’ve been posting pictures to social media about making stamps and some have asked how it’s done. I’m no expert, but over the past few weeks of trial and error along with a lot of research, I’ve been able to put together a pretty decent work flow.

Let’s start with what you’ll need. I’ve tried to include everything I use and included amazon, web links and stores where you can find these items.

For the stamp I’ll be making in this post, I used my drawing of a pumpkin and you can download it __here__ if you’d like to follow along with it.

Continue reading “Making Photopolymer Stamps: Materials List & Pictorial”

Making my mother some stamps with COLOP Photopolymer

My mother, after seeing my doodles and watercolor  post, suggested that I try making stamps, which sounded fun.   I had most of the equipment from other projects to give it a go.  All I really needed was the photopolymer.   After ordering a bottle of COLOP photopolymer off amazon, it showed up a few days later (it wasn’t even amazon prime, so I was impressed).

My first idea was to shove it into my 3D printer.  The whole idea behind my new printer was that it uses UV Resin, which is what a photopolymer is.   Shine a UV light on it and it cures.   It turns out that this stamping resin is so highly viscous that it’s barely a liquid and 3D printer resin is still quite liquid.   I started pouring it into the printer and it was hard to stop it from pouring because it was pulling itself out of the bottle.

Well, I can tell you that didn’t go well.   It was far too thick and the printer didn’t like it.  After editing the 3D printer’s program to see if I could make it work, I found the cured photopolymer wasn’t sticking to the platform and just ended up making a mess.

Continue reading “Making my mother some stamps with COLOP Photopolymer”

Kudo3d Bean on Indiegogo

Just under a year go I contributed to an Indiegogo campaign for a SLA printer called Bean and it finally showed up at my doorstep last week.

Kudo3D Bean Indiegogo showed up!

This printer has been basically been running non-stop since it showed up.  I’m having a lot of fun with it.  So far I’ve mostly been printing little figurines from one of my favorite 3d artists, who recreates a lot of characters I like.  I know his models are good and this has let me figure out all the ins-and-outs of printing with resin.

Continue reading “Kudo3d Bean on Indiegogo”

Creating a whole other messy room

I finally broke out some of my miniature kits that have been collecting dust.  The one I plucked out of the stack was a miniature craft room which is just crammed to the gill with stuff.   Why clean my craft room when I can spend time creating a whole other messy room right on my desk?

finished piece to my miniature sewing room kit

I forgot how long these take.  I’ve already spent several nights and I only have a few pieces put together.   It isn’t helping that these kits are usually from china, so the instructions are usually more confusing than helpful.   I’ve already messed up big once and ruined the two side pieces to this shelving unit.  I had to run to the store and buy more wood to make and paint those boards to match everything else.

Continue reading “Creating a whole other messy room”

Cheating with Watercolors

The other day I was poking around on my phone and decided to play with the stylus my Note 9 comes with.   I rarely touch it.  When I do use it, I use it for a long period of time and the Note 9’s stylus only holds a charge for 20-30 minutes.  This can be aggravating when you’re using it to draw since you have to keep taking breaks to let it charge for a few minutes.  Nevertheless, I was thinking about Fall, so I doodled out a pumpkin.pumpkin doodle from my phone

Now, I had a doodle on my phone, a ton of watercolor palettes sitting within eyesight of the couch I was sitting on and a new Cricut upstairs.   After letting those 3 facts bounce around in my head for a minute, I came up with a plan and uploaded my sketch to Cricut.   After shoving some watercolor paper into the machine, it drew out my pumpkin for me.

Continue reading “Cheating with Watercolors”

Custom Order of Pillows

Recently, a friend asked me to do a custom order of pillows for a wedding gift.  And because I can’t say no to anyone, I got out my laptop and started digitizing their invitation artwork and slapped it on some fabric and sewed a series of lovely pillowcases.

custom embroidered pillowcase

I was glad their artwork was line art as it made for an easy embroidery job.  Though, they did want gold thread, which is always a pain to work with.  Metallic threads constantly snap when you sew with them.

Once the job was finished and the pillows were delivered, I had some extra supplies left over and I hit up my home-girl, Jess, and asked if she wanted to learn how to sew pillowcases.

Jess learning to sew pillowcases

The hardest part was the cutting the fabric up for a very large pillow.   We worked through folding fabric to cut on a small mat and then sewed the pieces together.

I pretty quickly realized how spoiled I am with my monster sewing machine at home that threads itself and auto adjusts for different fabrics.  The fleece she picked out for her pillows was slipping and sliding all over, but with a few pointers she was sewing pillowcases like a pro!


jess' fabric painted pillow cases

After our little sewing session she went on to make more pillowcases and even did some fabric painting on them!  She painted them so well I thought she had bought precut iron-ons.

I actually taught someone something, so that was pretty cool.

Cricut Maker and Clear Linoleum

The other day, I had this bright idea to cram clear linoleum stamping material into the Cricut.   It just BARELY fit.

I downloaded a simple ‘thank you’ SVG file from the internet and let the Cricut have at it.   My idea was just to let it cut a single layer and then take it from there with my manual carving tools once the design was in place.

It wasn’t perfect but it actually started the design for me.  I did notice the blade getting caught in the material once or twice but it recovered shortly after.   Once cut, I ripped the linoleum off the mat and started carving away.  This is when I realized it is extremely difficult to see the design and accurately cut it out when the material is clear.

I tried putting color paper under it and and changing my lighting to be able to see the cuts better, but not much was helping.   I finally got out an ink block and patted it all down to get an idea of how I was doing so far.

That’s when I noticed my cuts weren’t great and a bunch of the initial cut wasn’t great either.   This was way too hard for a simple thank-you stamp.   So I tossed it and searched my other materials.   Unfortunately, everything else was slightly too thick to fit into the machine.

I’m trying to decide if I should try again with some different settings to see if I get better cuts, or do I see if I can get it to draw on the linoleum without destroying a marker.  I think it might cram the marker down too hard and screw up the tip if I don’t pick the right settings… I guess there’s only one way to find out!